-
UL Certified Fieldbus Closed loop Stepper Drive UST2556E
The EtherCAT fieldbus stepper drive UST2556E is based on the CoE standard framework and complies with the CiA402 standard. The data transmission rate is up to 100Mb/s, and supports various network topologies.
UST2556E matches closed loop stepper motors below 60mm.
● Control mode: PP, PV, CSP, Homing mode, etc
● Power supply voltage: 18-80VDC
● Input and output: 4-channel 24V common anode inputs; 2-channel optocoupler isolated outputs
● Typical applications: assembly lines, lithium battery equipment, solar equipment, 3C electronic equipment, etc
-
UL Certified Fieldbus Open loop Stepper Drive USR2556E
The EtherCAT fieldbus stepper drive USR2556E is based on the CoE standard framework and complies with the CiA402 standard. The data transmission rate is up to 100Mb/s, and supports various network topologies.
USR2556E matches open loop stepper motors below 60mm.
● Control mode: PP, PV, CSP, Homing mode, etc
● Power supply voltage: 18-80VDC
● Input and output: 2-channel differential inputs/4-channel 24V common anode inputs;
2-channel optocoupler isolated outputs
● Typical applications: assembly lines, lithium battery equipment, solar equipment, 3C electronic equipment, etc
-
UL Certified Fieldbus Closed Loop Stepper Drive UST2556M
Field bus stepper drive USD2556M is based on RS-485 network to run Modbus RTU protocol. The intelligent motion control
function is integrated, and with external IO control, it can complete functions such as fixed position/fixed speed/multi position/auto-homing
UST2556M matches open loop or closed loop stepper motors below 60mm
● Control mode: fixed length/fixed speed/homing/multi-speed/multi-position
● Debugging software: RTConfigurator (multiplexed RS485 interface)
● Power voltage: 24-50V DC
● Typical applications: single axis electric cylinder, assembly line, connection table, multi-axis positioning platform, etc
-
UL Certified Two Phase Open loop Stepper Drive USR2556
The USR2556 is an upgraded version of the open loop stepper driver launched by Rtelligent, and the product design idea is derived from our experience accumulation in the field of stepper drive over the years. By using a new architecture and algorithm, the new generation of stepper driver effectively reduces the low-speed resonance amplitude of the motor, has a stronger anti-interference ability, while supporting non-inductive rotation detection, phase alarm and other functions, support a variety of pulse command forms, multiple dip settings.
-
Integrated Drive Motor IR42 /IT42 Series
IR/IT series is the integrated universal stepper motor developed by Rtelligent, which is the perfect combination of motor, encoder and driver. The product has a variety of control methods, which not only saves installation space, but also convenient wiring and saves labor cost.
· Pulse control mode: pul & dir, double pulse, orthogonal pulse
· Communication control mode: RS485/EtherCAT/CANopen
· Communication Settings: 5-bit DIP – 31 axis addresses; 2-bit DIP – 4-speed baud rate
· Motion direction setting: 1-bit dip switch sets the motor running direction
· Control signal: 5V or 24V single-ended input, common anode connection
Integrated Motors are made with high performance drives and motors, and deliver high power in a compact high quality package that can help machine builders cut down on mounting space and cables, increase reliability, eliminate motor wiring time, save labor costs, at a lower system cost.
-
Fieldbus Open loop Stepper Drive ECT60X2
The EtherCAT fieldbus open loop stepper drive ECT60X2 is based on the CoE standard framework and complies with the CiA402 standard. The data transmission rate is up to 100Mb/s, and supports various network topologies.
ECT60X2 matches open loop stepper motors below 60mm.
• Control modes: PP, PV, CSP, CSV, HM, etc
• Power supply voltage: 18-80V DC
• Input and output: 8-channel 24V common positive input; 4-channel optocoupler isolation outputs
• Typical applications: assembly lines, lithium battery equipment, solar equipment, 3C electronic equipment, etc
-
PLC product presentation
The RX3U series controller is a small PLC developed by Rtelligent technology, Its command specifications are fully compatible with Mitsubishi FX3U series controllers, and its features include supporting 3 channels of 150kHz high-speed pulse output, and supporting 6 channels of 60K single-phase high-speed counting or 2 channels of 30K AB-phase high-speed counting.
-
2 Axis Stepper Drive R42X2
Multi-axis automation equipment is often required to reduce space and save the cost.R42X2 is the first two-axis special drive developed by Rtelligent in domesitic market.
R42X2 can independently drive two 2-phase stepper motors up to 42mm frame size. The two-axis micro-stepping and current must be set to the same.
• Speed control mode: the ENA switching signal controls the start-stop, and the potentiometer controls speed.
• Signal level: IO signals are connected to 24V externally
• Power supply: 18-50VDC
• Typical applications: conveying equipment, inspection conveyor, PCB loader
-
2 Axis Stepper Drive R60X2
Multi-axis automation equipment is often required to reduce space and save the cost. R60X2 is the first two-axis special drive developed by Rtelligent in domestic market.
R60X2 can independently drive two 2-phase stepper motors up to 60mm frame size. The two-axis micro-stepping and current can be set separately.
• Pulse mode: PUL&DIR
• Signal level: 24V default, R60X2-5V is required for 5V.
• Typical applications: dispenser, soldering machine, multi-axis test equipment.
-
Switch Stepper Drive Series
IO series switch stepper drive, with built-in S-type acceleration and deceleration pulse train, only need switch to trigger
motor start and stop. Compared with speed regulating motor, IO series of switching stepper drive has the characteristics of stable start and stop, uniform speed, which can simplify the electrical design of engineers.
• ontrol mode: IN1.IN2
• Speed setting: DIP SW5-SW8
• Signal level: 3.3-24V Compatiable
• Typical appications: conveying equipment, inspection converyor, PCB loader
-
Digital Stepper Driver R86mini
Compared with R86, the R86mini digital two-phase stepper drive adds alarm output and USB debugging ports. smaller
size, easier to use.
R86mini is used to drive two-phase stepper motors base below 86mm
• Pulse mode: PUL & DIR
• Signal level: 3.3~24V compatible; series resistance not required for the application of PLC.
• Power voltage: 24~100V DC or 18~80V AC; 60V AC recommended.
• Typical applications: engraving machine, labeling machine, cutting machine, plotter, laser, automatic assembly equipment,
• etc.
-
Digital Stepper Driver R110PLUS
The R110PLUS digital 2-phase stepper drive is based on 32-bit DSP platform, with built-in micro-stepping technology &
auto tuning of parameters, featuring of low noise,low vibration, low heating and high-speed high torque output.It can fully play the performance of two-phase high-voltage stepper motor.
R110PLUS V3.0 version added the DIP matching motor parameters function, can drive 86/110 two-phase stepper motor.
• Pulse mode: PUL & DIR
• Signal level: 3.3~24V compatible; series resistance not necessary for the application of PLC.
• Power voltage: 110~230V AC; 220V AC recommended, with superior high-speed performance.
• Typical applications: engraving machine, labeling machine, cutting machine, plotter, laser, automatic assembly equipment,
• etc.